Improved technology enables fast cutting, clean stripping and simple blade changeover for various size wires.


Without a sculptor, a piece of clay or marble can never reach its full artistic potential. Rotary, V and die

blades in automatic cutting and stripping machines serve a similar role to

help conductive wire and cable achieve its full electric potential as part of a harness. 


Within one or two seconds, these blades precisely cut each wire or cable to a predetermined length and remove

its insulation to expose one or more inner conductors. The wires or cables are then manually or automatically

crimped by terminal crimping machine

before being brought to the assembly workstation, where assemblers use boards to carefully build each

harness. 


At Gruber Communications, based in Phoenix, workers assemble lots of cable harnesses for use in data

centers every day. The company’s priority since day one has been to produce high-quality cables—and make sure

that no cable conductor, or high voltage cable

machine is ever nicked or blemished during

wire cutting and stripping machine's processing. 


For more than a decade, Gruber workers used separate pneumatic machines to cut and strip each cable.

Eventually, though, CEO Pete Gruber grew tired of the constant maintenance on the machines’ check valves and

cylinders. This led him to purchase the all-electric EcoStrip 9300 cut and strip machine in 1998. 


Made by Schleuniger AG of Switzerland, the machine’s reliability and infrequent need for parts has enabled

Gruber to substantially increase its cable harness production over the past 18 years. In fact, this machine

continues to precisely cut and strip cables after more than 6 million runs. 


Being able to run reliably for nearly 20 years and cut and strip millions of cables or wires is quite

common for today’s automatic machines. There are two reasons for this, say suppliers. First is stateof-

 the art blade technology, which enables fast cutting, clean stripping and simple blade changeover for

various size wires. Equally important are operators who understand, implement and optimize each machine’

s cutting and stripping capabilities. 


FROM SIMPLE TO PROGRAMMABLE 


More than 90 years ago, Haaken Olsen—an up-andcoming engineer at Artos Engineering Co.—noticed an

increased usage of insulated copper wire in automobiles, appliances and radios. He also saw assembly workers

manually measuring wire to predetermined lengths, cutting it and removing the insulation from both wire

ends. 


Believing manufacturers would be interested in buying an automated machine that could perform this

work faster, better and more cost-effectively, Olsen went about developing one. In 1926, Artos introduced the

CS-1, the first-ever automatic CAS machine. Olsen vowed to sell at least a dozen, but things went much better

than planned. A new industry was born, and Artos alone has sold nearly 100,000 wire processing machines over

the past nine decades. 


“Cutting and wire stripping machine machines

 from the 1920s to the 1950s featured mechanical designs,” explains John Olsen II, president of Artos

since 2005 and great-grandson of Haaken. “Typically, three pair of fixed-position blades were used to cut and

strip the wire. All setup changes were done mechanically by adjusting cams and moving blade spacers.” 


More-advanced electropneumatic CAS machines appeared in the 1960s and 1970s, allowing for push-

button control of feeding lengths. Since then, according to Olsen, CAS machines have evolved in three areas to

become much more efficient. 


One is the improved operator interface, which increases the machine’s capability to process small batch

sizes and provides full integration with a marking system (laser, inkjet, hotstamp) or slitting device.

Another is the use of servomotors for all wire movements to increase processing precision and speed. The third

is faster machine changeover by using quick-change guides and blades, and technology like the Artos Sencor

system to automate wire setup. 


Semi- and fully automatic CAS machines come in three sizes: benchtop, midsize and large. A benchtop model

is best for low-volume and prototyping applications. It usually requires little setup, plugs into a standard

110- volt outlet, and is simple to operate (push buttons, small display, limited programming). 


Despite being an entry-level machine, the benchtop EcoStrip 9380 from Schleuniger can process single wires

from 30 to 8 AWG and two wires (up to 0.12-inch diameter) in parallel. It is operated via S. ON software on a 5.7-

 inch color touch screen, and features the company’s Bricks electronic platform for precise wire feeding

by using automatic wire prefeeder. An optional

belt feeding system can be set for normal, roller or short mode processing. 


Midsize machines are designed for medium-volume applications, which suppliers define as processing up to

a few thousand wires or cables per week. These machines may or may not be standalone, but they are bigger

and offer more programming options than benchtop models. 


One such unit is the CS-326 from Artos. The fully electric, servo-driven machine processes wire

and cable from 30 to 4 AWG or 0.5 inch OD. It cuts wire to a length of 0.25 inch to 3,250 feet. Minimum

and maximum stripping lengths are 0.01 inch and 39 inches, respectively. 


The machine features the Sencor system that senses the conductor within the wire and automatically sets

blades at the proper stripping diameter. This technology reduces wire waste, shortens setup time and monitors

blade wear. 


Separate accessories enable the unit to cut Kevlar-insulated wire and strip coaxial and ignition cables.

An optional work table lets companies easily move the 400-pound machine to any workstation. 


Schleuniger offers six versions of its MultiStrip 9480 machine to cover a wide range of applications (32 to

8 AWG wire) and budgets. Four models (MR, RS, RSX and RX) feature a fully programmable rotary

incision unit capable of processing coaxial and multilayer cables. A multiposition indexing cutter head,

standard on all models except the S, accepts blade cassettes that change out quickly and easily. The machine

cuts and strips wire as short as 2.3 inches and as long as 3,281 feet. In short mode, wires as short as 0.375

inch, with a 0.125-inch strip length on each end, can be processed. 


Large machines are for high-volume (up to several thousand pieces per shift) processing of

singleconductor wire as large as 4/0 AWG, and multiconductor or shielded cable up to 1.5 inches OD. These

standalone units feature large cutter heads, infeed and outfeed mechanisms, an HMI and multiple protocol

interfaces. Users of these machines usually require one to two days of hands-on operations training by

the supplier. 


Most large machines can also be networked with other assembly machines via a plant’s ERP and

MES software. Manufacturers especially like this capability because it provides full traceability for every

job, and enables them to track how many cycles each machine has completed and when maintenance should be

scheduled.


 Artos’ CS-327 machine processes cables as large as 4/0 AWG or 1.37 inches in diameter, including

battery and welding cables, power cables for appliances, and multiconductor cables for signal and power. The

unit’s dualblade cutter head and belt infeed and outfeed systems are servo-driven. Minimum wire cut length is

10 inches in standard mode and less than 2 inches in short mode. Strip lengths are programmable to 40

inches. 


Also standard are an integrated length encoder for accuracy and quality, an HMI for PC operator control and

a removable wire scrap collection tray. Options include a three-blade cutter head for high-speed processing

and special tooling for steel cables. 


FEWER CHALLENGES THAN BEFORE 


“In the 1950s, the average harness in an American car contained fewer than 50 wires,” notes Rob Boyd, senior

product manager at Schleuniger. “Today’s car features many harnesses that have hundreds of wires of varying

gauges and lengths. As a result, harness makers need versatile [url=http://www.automaticwirestrip.com/automatic-

cutting-machine/]automatic cutting machine[/url] and stripping machines to meet this challenge.” 


They also need to make sure that their machine operators are trained to understand the dynamics that

exist between wire insulation (depending on wire supplier), nonsymmetrical wire, and blade design and

performance limitations. Tim Crider, sales director at Komax Wire, cites as an example the lower margin of

error when processing PVC-insulated wire as compared to Teflon-insulated wire. Because PVC is softer and less

challenging to cut and strip, the operator doesn’t need to pay as close attention to process

parameters, blade positioning and wear. 


Komax’s Kappa 331 machine addresses these and many other challenging applications. It processes wire from

24 to 2 AWG and cable up to 0.63 inch OD in large and small batches. The unit also performs full and partial

pull-off operations on single conductors and individual coax layers, and strips the outer jackets from

cables with or without shielding. 


A key feature is the Kappa Sensorik laser sensor, which automatically detects the wire conductor and

uses inductive measuring to determine its diameter. The sensor and a chargecoupled device (CCD) line

optically measure the outside cable diameter and then check that the cable is present during processing. This

feature greatly shortens setup time and changeover, and reduces operating errors. 


For the past 18 months, a large wire harness and cable manufacturer has been using the Kappa 322 machine to cut

and strip three-conductor 14 AWG cable (40 inches long) at a rate of 600 pieces per hour (pph). This

midsize unit processes wire from 30 to 4 AWG and enables easy setup and changeover without tools. 


“Buying a midsize machine to constantly perform heavy-duty work is a common problem,” says Armando

Zacarias, sales and service manager at Eubanks Engineering Co. “A machine that’s capable of

processing 32 to 8 gauge wire is really not designed to process 8 gauge wire all day long. Using the

machine that way will likely require it to often be refurbished or rebuilt. A better approach is to buy a

machine that’s able to process wire as large as 4 gauge.” 


Operators use a cassette to quickly insert and remove blades from Eubanks’ fully programmable AirStrip

7400 machine. Microprocessor-controlled and easy to operate, the machine handles stranded conductor wire

from 32 to 8 AWG, and multiconductor cable up to 0.31 inch OD. It strips cable up to 20 inches long, and can

be programmed to do step and center stripping. 


A bit larger in size is the more powerful 2700-05. It cuts and strips wire from 32 to 8 AWG, as well as

multiconductor and flat cable up to 0.31 inch wide. Operators input wire processing parameters on the built-in

keypad. Zacarias says consumer electronics and automotive manufacturers use this machine in high-volume, low-

mix environments because of its high production rate (up to 10,800 pph). 


Another ongoing challenge is making the wire and cable as straight as possible before it enters the CAS

machine. Suppliers often provide material on the smallest spool possible, which, unfortunately, results in

bent wire and cable that may require a straightener. 


To avoid this extra processing step, Boyd recommends thin wire be wrapped around spools at least 10 inches

in diameter. Thicker wire and cable should be delivered on much wider barrels, so that it unwinds in a large

loop that is easy to straighten.